How to Replace a Saab 9-3 Key The Saab 9-3 has a good amount of appeal for drivers. It has excellent visibility and a powerful performance engine. It has a very high safety rating. It is important that you have two keys that work for your vehicle. If you lose the only key, it can be costly to purchase a new one. How to Replace the Ignition Key on the Saab 9-3 You'll must change your car key when it doesn't turn. This guide will walk you through the steps to do it on a Saab 9-3. You will have to replace the key, get an updated reprogrammable phone, and buy a new case for your key-fob. Unlike older models, most modern Saab vehicles use transponders in the key-fob, instead of a physical key that can be used to unlock and start the car. The reprogrammable batteries that are in the key-fob will eventually expire, and they will not be able to hold charge. This is particularly relevant if you continue to use the same key on the same lock. A professional locksmith can change the battery quite easily. You can also do it yourself if you have the proper tools and a bit of patience. The first step is to remove the key-fob. This is done by inserting a flathead screwdriver in the slot that is located in the middle of the case. It is essential to be careful, as the plastic is thin and is susceptible to damage. Once the case has been opened, you can make the new key by combining lower part of the key from earlier with a transponder and banana. This will ensure the new key is properly connected to your CIM that can make a significant difference when replacing the sole key for your Saab 9-3. How do I replace the ignition Key in a Saab 900 If you don't have two keys, you'll need to remove the dashboard and steering wheel to get to the ignition. Start by disconnecting the negative battery cable. Once the battery is removed, you can remove all trim pieces and dashboard pieces that surround the steering wheel. After the dashboard is removed, you can push a screwdriver into the opening behind the ignition switch and remove it. The ignition cylinder comes with a lock for keys that can prevent the vehicle from starting if you don't contain the key. If the ignition switch on your 900 doesn't work correctly, make sure to check if the key is in the lock or snared inside the ignition barrel. You should also rotate your keys and keep them clean to prevent bending. Saab cars differ from other cars in that they don't have traditional metal keys. Instead, the car detects the electric signals of the key fob through a special chip embedded in it. If you have lost your only working key fob the dealer will charge you the highest dollar to replace your computer module (known as the CIM). However, we can reprogram the existing computer's EEPROM and set it to accept new keys without replacing it. This can save you over 50% of what the dealer charges! This is the SAAB Key PROGRAM. Find out more information about it here! How to Replace the Ignition Key on a Saab 9-5 The metal component of a traditional Saab key is easy to duplicate, and it's not much of a deterrent against vehicle theft. The real protection comes from the electronic part inside the key-fob. It contains a chip that recognizes your car when it's inserted into your ignition switch. saab replacement keys -theft system has been relying on this technology for more than 10 years. It's not quite as effective as a door lock but it does make stealing your car a lot harder. Every Saab owner must keep a spare Saab key in their car. The majority of new Saabs are delivered with two keys. However, they can be added by a dealer using a special handheld device known as a Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception to this rule is the NG 9-3 vehicles with more modern, more advanced features that require the use of a key-fob. The dealer will replace the CIM or TWICE module in these cars if the keys are lost. They'll cost you top dollar for doing it. However, we can reprogram the EEPROM in your existing computer to accept new keys, without having to replace the expensive modules. How do I replace the ignition Key on the Saab XC90 It's possible to replace your SAAB key fob if you are experiencing difficulty turning the lock barrel. It's a simple process and you don't even need to go to a dealership. You can complete the process at home using just a few basic tools. The first step is to prepare the new key. Before you start, disable the anti-theft feature by placing blocks underneath your rear wheels and engaging your handbrake. Put the key into the ignition and turn the key to the on position. This will activate the accessories, but will not start the engine. Repeat this procedure 5 times, and then put the key in the on position. The next step is to buy a new case for the old key fob. They can be found at any auto parts shop, and they're generally quite affordable. Based on the model, you may even buy them without electronics. To open the case you need to gently push the flathead screwdriver into the slot in the middle. The case will split easily, and when you have it, you'll be able to gain access to the internal electronics. To get rid of the electronics, use a small screwdriver and try prying them out gently.
saab replacement keys
